Stick a plate to the ceiling and the light snaps on by magnet. No wiring, no drilling, no landlord, no electrician.
Motion Sensor Ceiling Light: Installs in 30 Seconds
$19.99
$33.32
SAVE
40%
Pull the light off the plate, plug in USB-C, snap it back when charged. No batteries to buy. Battery lasts weeks between charges on auto-off mode.
Turns on when you walk under it, off after you leave. No switch.
Warm, neutral, or cool white. Dim for night glow or full for task.
⭐
No Tools Required
Stick and snap
🏆
USB Recharge
No battery replacements
✨
30-Second Setup
Shown on camera
Jess M.
Renting and can't drill, finally just ordered it. Literally why did I wait two years they look like regular lights I love them and they have different modes
Over 8,000 Rooms That Finally Have Light
Motion Sensor Ceiling Light 2-Pack: 30-Second Install
Forgot about the remote for a week
The motion sensor just works so I never had to touch the remote after setup.
If you rent, get this
I bought it for my own hallway and now I've gotten one for three friends who are also stuck in apartments with no overhead lights. If you're not allowed to drill or wire anything, this is the answer.
I kept waiting for the catch
I've been living with a pitch-black hallway for four years because my landlord won't let me touch the ceiling. Saw the thirty-second install video and figured it was too good to be true, but I was so tired of fumbling for my phone at 2 AM. Stuck it up, works exactly like they showed.
No more phone flashlight
I used to walk into my bedroom closet with my phone light on every single morning because there's no switch in there. Now I just walk in and it lights up by itself. I haven't used my phone as a flashlight in my own house in three weeks. That sounds small but it was every day, twice a day, for two years.
Still stuck up there three months in
I was sure the adhesive would peel off my textured ceiling in a week. It hasn't budged. I check it every time I walk under it.
Perfect for renters who can't drill
My lease says no holes in the ceiling, so I've been stumbling through my hallway in the dark for two years. Stuck the plate up, snapped the light on, and now it just works. I didn't think it would be that simple but it actually was.
Didn't know I'd stop turning on the switch
I put one in the hallway and one in the pantry, and now I realize I haven't flipped a light switch in either room in three weeks. The motion thing just does it for you, which sounds small until you're walking out with an armful of laundry or groceries and you don't have to fumble for anything.
If you rent or have older parents, get this
I got two for my mom's hallway after she fell trying to find the light switch at night. Now the light just comes on when she walks through. If you have aging parents or you're in a rental where you can't change anything, this is the answer. Took me maybe a minute to put up and she hasn't had to feel around in the dark since.
Thirty bucks felt safer than calling my landlord
I wasn't sure it would stick or stay bright, but asking permission to drill seemed worse. Bought it, stuck it up in the hallway, and now I just walk through at night without a phone flashlight.
There's a Room in Your Place With No Ceiling Light and No Way to Add One
Stick the Plate Up. Snap the Light On. Done.
You've been living with that dark closet, hallway, or pantry for years. An electrician wants three hundred dollars to run one wire.
Your landlord says no drilling. You're not handy and you hate waiting on someone who is. So the room stays dark and you hunt for shoes.
Candles and plug-ins layer perfume over a smell that's still there. The odor never left. You masked it, and the moment the candle burns out, it's back.
This is real overhead light that installs in thirty seconds. Peel the adhesive backing off the metal plate, press it to the ceiling, line up the magnets, and snap the light on. No wiring, no drilling, no electrician. The motion sensor turns it on when you walk under it and off after you leave.
Magnet-mount. Install in 30 seconds flat.
Motion sensor. Turns on when you walk in.
USB-C rechargeable. No batteries to buy.
Why Magnetic Ceiling Lights Beat Battery Puck Lights
Battery puck lights dim without warning, fall off the ceiling mid-winter, and die when you need them. Magnetic ceiling lights snap on, charge when the battery runs low, and stay put because the magnet holds stronger than any adhesive disc ever could. One is a temporary fix. The other is the overhead light the room should have had from the start.
Why Magnetic Ceiling Lights Beat Battery Puck Lights
Battery puck lights dim without warning, fall off the ceiling mid-winter, and die when you need them. Magnetic ceiling lights snap on, charge when the battery runs low, and stay put because the magnet holds stronger than any adhesive disc ever could. One is a temporary fix. The other is the overhead light the room should have had from the start.
|
Magnetic Motion Sensor Light
|
Battery Pucks
|
|
|---|---|---|
|
Magnetic mount holds 8+ lbs. Pull test required to remove
|
||
|
Rechargeable. Charge when low, not when it dies on you at night
|
||
|
No batteries to buy, no dead-light surprise
|
||
|
Motion sensor turns it on when you walk under it
|
||
|
Remote picks warm, neutral, or cool white and dims it down
|
||
|
30-Day Money-Back Guarantee
|
The Closet That Lights Itself When You Open the Door
1,900+ renters, homeowners, and the adult children who installed one for Mom
The Closet That Lights Itself When You Open the Door
1,900+ renters, homeowners, and the adult children who installed one for Mom
0%
Installed It Without Calling for Help
0
Weeks Between Charges (Daily Use)
0
Light Modes (Warm, Neutral, Cool White)
The Rechargeable Motion Sensor Ceiling Light sticks to the ceiling by magnet. The adhesive plate holds the magnet. Independent pull tests measured 8.2 lbs of force required to remove the light from a painted drywall ceiling after 30 days of mounted use.
The Room With No Light Finally Gets One
You have a closet, hallway, pantry, or garage corner with no ceiling fixture and no switch. An electrician costs three hundred dollars and two weeks. Your landlord says no drilling. So you've been fumbling for a lamp cord or living in the dark for years.
Peel the adhesive backing off the metal plate. Stick it to the ceiling. Line up the light disc and let the magnets pull it into place. That is the entire installation. Thirty seconds, no tools, no waiting on anyone.
Walk under it and the motion sensor flips the light on. Leave and it turns itself off. The remote in your hand picks warm white for a bedroom, neutral white for a closet where navy and black look the same, or cool white for a workbench. Dim it down for a hallway night glow or run it full for task light. Set the timer and the light shuts itself off after you walk away.
Two lights in the box. Two dark rooms handled in one sitting.
How to Install It
1
Stick the Plate Up
Peel the adhesive backing, press the metal plate to the ceiling, hold for ten seconds. Works on smooth paint and drywall.
2
Snap the Light On
Line up the magnets and the light snaps to the plate. Walk under it and the motion sensor turns it on for you.
3
Charge When Low
Pull the light off the plate, plug in the USB-C cable, snap it back when charged. Battery lasts weeks on auto-off.
Not a puck light. A full ceiling fixture you mount.
Battery puck lights give you six dim hours, then die without warning in the middle of the night. This is a rechargeable LED ceiling disc that snaps to a magnetic plate and stays there until the motion sensor job is done. When the charge runs low, pull the light off the plate, plug in the USB-C cable, and snap it back up. No disposable batteries. No mid-week runs to the hardware store because the closet went dark again.
-
Magnetic Mount. Plate Sticks Up, Light Snaps On, Done
-
Motion sensor, turns on when you enter the room
-
Remote Picks Warm, Neutral, or Cool White. Dims Down or Runs Full
-
USB-C Rechargeable. No Batteries to Buy or Swap
Rechargeable Motion Sensor Ceiling Light Questions
How well does the adhesive plate hold to the ceiling?
+
The mounting plate uses industrial-strength adhesive designed for overhead weight. It holds firmly on smooth ceilings like drywall, paint, tile, and laminate. For textured or popcorn ceilings, screws provide a more secure hold and are included with the mounting hardware. The magnet connection is strong enough that the light stays in place until you pull it straight down to charge it.
Do I need to drill or wire anything to install this?
+
No drilling and no wiring. You peel the backing off the adhesive plate, press it to the ceiling, and snap the light onto it by magnet. The entire install takes about 30 seconds per light. If you're working with a textured or popcorn ceiling, screws are the better option and come with the kit, but you still never touch a wire.
How do I recharge it, and how often does that need to happen?
+
Pull the light straight down off the magnetic plate, plug the included USB-C cable into any USB port or phone charger, and snap it back up when it's charged. In a closet that opens six times a day, you charge every three to four weeks. A hallway with twenty walks per day runs six to eight weeks between charges. No batteries to buy or replace.
Does the motion sensor work during the day or only in the dark?
+
The motion sensor activates any time you walk under the light, day or night, regardless of ambient light levels. It detects motion within its range and turns the light on immediately, then switches off automatically after you leave. You're not waiting for the room to go pitch black before it responds.
Can I control the brightness and color of the light?
+
Yes. The included remote lets you pick warm white for bedrooms and evening use, neutral white for closets where you need to see color accurately, or cool white for work areas like garages and laundry rooms. You can also dim the light down for a soft night glow or turn it up to full brightness for task lighting. The timer function on the remote turns the light off after a set period if you want it to shut down on its own.